Do you have a 2-post car lift control board that needs testing, but you are not sure whether the PCB is faulty, repairable, or needs to be replaced?

Pro-Logic Technologies provides electronic troubleshooting, industrial PCB diagnosis, control board testing and component-level PCB repair in Industrial Area, Nairobi, Kenya.

We work with customers who have faulty electronic control boards from industrial machinery, automotive workshop equipment, vehicle lifts, power systems, appliances and other electronically controlled equipment.

If your machine has stopped working and the control PCB is suspected to be responsible, the best place to start is with a proper diagnosis.

A control board can fail in many different ways. Sometimes the fault is obvious, such as a burnt component or damaged PCB track. In other cases, the board may look completely normal while having an electrical fault that can only be identified through testing.

For this reason, PCB diagnosis comes before major repair decisions.

Industrial PCB Repair in Industrial Area Nairobi

Industrial Area is one of Nairobi's major commercial, engineering, manufacturing and automotive service locations. Businesses operating in this area rely on machinery, workshop equipment, electronic control systems and industrial automation.

When electronic equipment fails, finding a technician who understands PCB-level troubleshooting can be important.

At Pro-Logic Technologies, we provide industrial electronic repair solutions in Industrial Area, Nairobi for customers with suspected PCB faults.

Our service can include:

Industrial PCB testing
Industrial control board diagnosis
Control PCB troubleshooting
Component-level PCB repair
Relay board repair
Power supply board diagnosis
Machine control board repair
Automotive equipment PCB diagnosis
Vehicle lift control board testing
Two-post car lift controller diagnosis
Electronic control module troubleshooting
Industrial electronics fault finding

Each PCB is different, so the exact repair process depends on the board design, fault symptoms and condition.

2-Post Car Lift Control Board Repair in Industrial Area

One of the important applications of industrial electronic control boards is automotive workshop equipment.

Two-post vehicle lifts are widely used by garages and automotive service centres.

The lift's electronic control system can contain a PCB that communicates with or controls various components of the equipment.

Depending on the particular lift design, the control board may interact with:

Push buttons
Emergency stop switches
Limit switches
Relays
Contactors
Hydraulic solenoids
Motor controls
Safety circuits
Indicator lamps
Sensors
Control transformers
Power supplies
Other control modules

If the PCB develops a fault, the vehicle lift may stop operating correctly.

Possible symptoms include:

Lift does not power on
Lift has power but does not raise
Lift raises but does not lower
Lift lowers but does not raise
Motor does not start
Hydraulic pump does not activate
Relay does not click
Relay clicks but equipment does not operate
Control buttons do not respond
Emergency stop circuit appears abnormal
Limit switch input is not recognised
Indicator lights do not work
Control output is missing
Fuse repeatedly blows
PCB overheats
Lift operates intermittently
Controller stopped after a power surge

These symptoms do not automatically prove that the PCB is defective.

A proper diagnosis is necessary.

Professional Control PCB Diagnosis in Industrial Area

A control PCB is the electronic brain or interface of many machines.

However, the PCB is only one part of the complete equipment.

A vehicle lift, for example, can have electrical, electronic, hydraulic and mechanical systems working together.

If the lift refuses to raise, the cause could be:

Control PCB
Push-button assembly
Safety switch
Limit switch
Relay
Contactor
Motor
Solenoid
Wiring
Power supply
Hydraulic system
Mechanical system

This is why replacing the PCB without diagnosis can be expensive and ineffective.

Our objective is to determine whether the control board is actually responsible for the problem.

What Is Industrial PCB Diagnosis?

Industrial PCB diagnosis is the systematic process of determining whether an electronic control board has a fault and, where possible, identifying the faulty circuit section or component.

The process can include several stages.

Visual Inspection

The board is inspected for signs of:

Burning
Overheating
Cracked components
Corrosion
Water damage
Broken tracks
Damaged terminals
Loose connectors
Failed capacitors
Damaged relays
Poor solder joints
Previous repair work

Visual inspection is useful, but it is only the beginning.

A PCB can look normal and still be defective.

Electrical Testing

Electrical testing may involve checking relevant circuit sections for:

Input voltage
Output voltage
Supply rails
Continuity
Resistance
Short circuits
Diode operation
Relay coils
Switching components
Voltage regulators
Control signals
Power-supply components

The exact tests depend on the board.

The purpose is to establish how power and control signals move through the circuit.

Control Signal Testing

An industrial control PCB may receive an input and produce a corresponding output.

For example, a button may send a command to the controller.

The controller may then activate a relay.

The relay may operate a contactor.

The contactor may switch a motor.

If the sequence stops at one point, that provides an important diagnostic clue.

A good technician therefore does not simply ask:

“Does the PCB have power?”

The more useful questions are:

Is the correct power entering the board?

Are the required supply voltages present?

Is the control input reaching the board?

Is the controller processing the input?

Is the expected output being generated?

Is the output driver working?

Is the external equipment responding?

This systematic approach can help locate the actual fault.

How Much Do You Charge for PCB Diagnosis?

Customers frequently ask:

“What is your charge for diagnosis?”

Industrial control boards vary considerably in complexity.

A simple relay-control board may require considerably less diagnostic work than a complex industrial controller containing multiple power supplies, processors, switching circuits and safety interfaces.

Therefore, the diagnostic charge depends on the PCB and the testing required.

Before extensive repair work is undertaken, the board can be assessed and the customer advised about the applicable diagnostic and repair process.

The important distinction is between:

Diagnosis

and

Repair.

Diagnosis determines what is wrong.

Repair involves correcting the identified fault.

A customer may choose to proceed with repair after receiving the diagnostic findings.

Why PCB Diagnosis Is Important

Replacing an industrial control board can be expensive.

There is also no guarantee that a replacement board will solve the problem if the actual fault is somewhere else.

For example, an external short circuit could have damaged a PCB output.

If the short remains and a new PCB is installed, the replacement board may also become damaged.

Similarly, a faulty motor, solenoid, sensor, wiring connection or power supply may create symptoms that appear to originate from the PCB.

Professional diagnosis helps separate:

PCB faults

from

equipment faults outside the PCB.

Industrial Control Board Testing

Industrial control boards can contain multiple circuit sections.

A typical board may include:

AC input
DC power supply
Rectifier
Voltage regulator
Control circuit
Microcontroller
Relay drivers
Relays
Transistors
Optocouplers
Protection devices
Input circuits
Output circuits
Connectors
Communication interfaces

A failure in one section can affect the operation of the complete machine.

Testing should therefore be performed logically.

Industrial Control PCB Repair Services

Pro-Logic Technologies can assess various types of industrial electronic boards.

Our industrial PCB service may include:

Control PCB Diagnosis

Determining whether a control board has an identifiable fault.

PCB Testing

Checking relevant electrical sections of the board.

Component-Level Repair

Investigating defective individual components where practical.

Relay Repair

Testing relay coils, contacts and associated driver circuits.

Power Supply Repair

Investigating failed or abnormal PCB power-supply sections.

Track Repair

Repairing certain damaged PCB tracks where technically practical.

Connector Repair

Investigating damaged or unreliable board connections.

Solder Joint Repair

Addressing certain cracked or defective solder joints.

Industrial Electronics Troubleshooting

Investigating electronic faults affecting industrial machinery and workshop equipment.

Component-Level PCB Repair in Nairobi

A PCB does not necessarily need to be replaced simply because one component has failed.

Depending on the board, it may be possible to repair the defective section.

Potential components that may require investigation include:

Resistors
Capacitors
Diodes
Zener diodes
Transistors
MOSFETs
Voltage regulators
Rectifiers
Optocouplers
Relays
Relay drivers
Fuses
Protection devices
Connectors
Switching components

Component-level repair is not always possible.

Some industrial boards contain proprietary integrated circuits, custom processors or discontinued components.

The condition of the PCB must therefore be assessed before a repair can be confirmed.

2-Post Car Lift PCB Troubleshooting

If your two-post car lift has stopped working, start by recording the symptoms.

For example:

Symptom: Lift completely dead

Possible areas requiring investigation include the incoming supply, protection circuit, power supply and control board.

Symptom: Lift has power but will not raise

Possible causes may include the control circuit, safety input, relay, contactor, motor circuit, hydraulic system or other equipment.

Symptom: Lift raises but will not lower

Possible causes may include control outputs, switches, solenoid control, safety circuits or external equipment.

Symptom: Relay clicks but motor does not start

The relay may be functioning while the downstream contactor, wiring, motor or power circuit has a fault.

Symptom: Fuse repeatedly blows

There may be a short circuit, overloaded component or external fault.

The PCB should be tested rather than repeatedly replacing fuses.

Symptom: Board works intermittently

Possible causes include poor solder joints, connectors, unstable power supply, overheating, damaged tracks or failing components.

The exact cause must be established through diagnosis.

Car Lift Control Board Testing in Industrial Area

If you are based in or around Industrial Area, Nairobi, you can bring a suspected vehicle lift control PCB for assessment.

Before bringing the board, it is helpful to provide photographs.

Send:

Front of PCB
Back of PCB
Part number
Model number
Manufacturer information
Control panel
Machine
Damaged area, if visible

Also explain what happened.

For example:

“The lift was working normally, then stopped after a power outage.”

or:

“The lift has power, but the raise button no longer activates the motor.”

This information can help establish the likely diagnostic direction.

Industrial PCB Repair for Automotive Garages

Automotive workshops depend on equipment that needs to remain operational.

A defective vehicle lift can prevent mechanics from carrying out:

Brake repairs
Suspension work
Exhaust repairs
Undercarriage inspection
Oil service
Transmission work
General vehicle maintenance

If the problem is electronic, the control PCB may require testing.

Instead of immediately purchasing a replacement controller, have the suspected board assessed.

Garage Equipment Control Board Repair

Modern garage equipment can contain sophisticated electronics.

Examples include:

Vehicle lifts
Wheel balancers
Tyre changers
Compressors
Battery chargers
Welding machines
Diagnostic equipment
Air-conditioning service equipment
Hydraulic equipment
Workshop machinery

These systems can use PCBs to control motors, valves, sensors and safety circuits.

A failure in the control electronics can make otherwise functional equipment unusable.

Industrial Electronics Repair in Nairobi

Pro-Logic Technologies provides electronic troubleshooting services for industrial and commercial equipment in Nairobi.

Our focus is on identifying faults rather than replacing components without evidence.

We understand that customers want to know three things:

Is my PCB faulty?
Can it be repaired?
How much will repair cost?

The first question is answered through diagnosis.

The second depends on the fault and board condition.

The third can be estimated more accurately once the fault has been identified.

PCB Repair After Power Surge

Power fluctuations and surges can damage control boards.

A surge may affect:

Fuses
Rectifiers
Capacitors
Regulators
Transistors
MOSFETs
Power supply controllers
Relay drivers
Integrated circuits
Protection circuits

Some surge damage is immediately visible.

Other damage is not.

If your control board failed after:

Lightning
Power restoration
Generator changeover
Electrical surge
Voltage fluctuation
Short circuit

tell us when requesting diagnosis.

The event may provide an important clue.

Industrial PCB Repair After Lightning Damage

Lightning-related damage can range from a simple protection component failure to severe damage across several circuit sections.

The board may appear partially functional.

For example, an indicator may still illuminate while the main control circuit has failed.

A diagnosis is necessary to determine the extent of damage.

PCB Repair After Water Damage

Moisture can cause:

Corrosion
Short circuits
Leakage paths
Connector damage
Track corrosion
Component failure

Water-damaged PCBs require careful inspection.

If your control board has been exposed to water, oil, chemicals or excessive humidity, mention this during the initial enquiry.

Relay Control Board Repair

Relays are commonly used in industrial equipment because they allow a control circuit to operate another electrical circuit.

A defective relay can cause:

No output
Intermittent output
Permanently active output
Clicking without operation
Overheating
Contact failure

However, relay replacement alone may not solve the problem.

The relay driver and external load should also be considered.

Motor Control PCB Diagnosis

Some industrial control boards interact directly or indirectly with motors.

A motor-related PCB fault can involve:

Control signals
Relay drivers
Contactors
Protection circuits
Switching devices
Power supplies

If a machine motor is not responding, the PCB should not automatically be blamed.

The motor and associated electrical system may also require inspection.

Hydraulic Equipment Control Board Repair

Hydraulic machinery frequently uses electronic controls to activate valves, pumps or other components.

A hydraulic system can therefore have both electronic and mechanical causes of failure.

For a vehicle lift, the electronic controller may command the hydraulic system while the actual lifting force is produced by mechanical and hydraulic components.

If the control board is functioning correctly, the problem may be elsewhere.

If the board is defective, repairing the electronic control section may restore the control signal.

Industrial Control PCB Fault Finding

Fault finding involves following the circuit logically.

Instead of replacing multiple components, we attempt to identify where expected behaviour stops.

For example:

Input → Controller → Driver → Relay → External Device

If the input is present but the controller produces no output, the fault may be in the controller or its supporting circuit.

If the controller output is present but the relay does not activate, the driver or relay may require investigation.

If the relay activates but the external device does not operate, the problem may be outside the PCB.

This method reduces guesswork.

Industrial PCB Inspection

A detailed PCB inspection can identify evidence of:

Burn marks
Cracked components
Broken connectors
Loose terminals
Corrosion
Contamination
Overheating
Previous repair
Damaged solder joints
Broken tracks

Photographs can provide useful initial information, but physical testing is often required for a definitive diagnosis.

Repairing Damaged PCB Tracks

PCB tracks carry electrical signals and power between components.

A damaged track can result from:

Overcurrent
Short circuit
Physical damage
Corrosion
Excessive heat
Previous repair work

Some damaged tracks can be repaired.

However, repairability depends on the location and extent of the damage and whether the PCB substrate and surrounding circuitry remain usable.

Industrial PCB Connector Repair

Connectors are critical because they connect the control board to the rest of the machine.

A damaged connector can cause:

Intermittent operation
Complete loss of a control signal
Overheating
Poor contact
Incorrect operation

Connector problems should be considered during PCB diagnosis.

Industrial PCB Solder Joint Repair

Repeated vibration and thermal cycling can affect solder joints.

A cracked joint can create intermittent electrical contact.

The machine may work normally at one moment and fail later.

If moving or tapping the board appears to change its behaviour, do not continue operating the equipment in that condition. The board should be properly inspected.

Industrial PCB Repair for Older Machines

Older machinery can remain mechanically useful long after its original electronics have become difficult to source.

If a replacement control board is unavailable, repairing the existing PCB may be worth considering.

Older boards can suffer from:

Ageing capacitors
Relay wear
Corrosion
Heat damage
Solder-joint problems
Connector deterioration
Component failure

A PCB assessment can help determine whether restoration is practical.

Obsolete Control Board Repair

An obsolete PCB does not automatically mean the machine is beyond repair.

Some boards can still be repaired using available replacement components.

However, proprietary processors, custom ICs and unavailable firmware can make certain repairs impractical.

The correct approach is to inspect the board first.

Industrial PCB Repair for Imported Equipment

Many businesses in Nairobi operate imported machinery.

Replacement control boards may sometimes be difficult or expensive to obtain.

If your machine was imported and its control board has failed, provide the manufacturer, model and PCB part number.

We can assess the board for possible electronic faults.

Why Customers Choose PCB Repair

PCB repair may be considered when:

Replacement boards are expensive.
Replacement boards are unavailable.
The machine is otherwise mechanically sound.
The original controller is discontinued.
The fault appears limited to a particular circuit.
Repair is economically sensible.

The decision should be based on diagnosis rather than assumption.

Repair Versus Replacement

There are two primary options when a control board fails.

Repair the Existing Board

This may preserve the original equipment configuration.

It can be particularly useful when a replacement board is unavailable.

Replace the Board

Replacement may be better when the existing PCB is severely damaged or when a reliable compatible replacement is readily available.

Diagnosis helps determine which route makes sense.

Can the PCB Be Tested Without the Machine?

In many cases, some PCB tests can be performed separately.

However, complete functional testing may not always be possible on a workbench.

A board may depend on:

Sensors
External relays
Machine-specific wiring
Communication signals
Special inputs
External loads
Safety circuits
Programming

Therefore, a bench diagnosis and complete machine test are not necessarily the same thing.

If the machine is available, additional system-level testing may sometimes be useful.

What Information Is Needed for PCB Diagnosis?

The following information is particularly helpful:

Machine manufacturer

For example, the vehicle lift manufacturer.

Machine model

The exact model if available.

PCB number

Any part number printed on the board.

Voltage rating

The relevant electrical specification.

Fault symptoms

What happens when you operate the machine?

Fault history

What happened immediately before the problem?

Photographs

Clear images of both sides of the PCB.

Wiring information

A wiring diagram is useful where available.

Industrial PCB Repair Cost in Nairobi

Industrial PCB repair costs vary.

A simple fault involving a replaceable component is different from a board with extensive damage or proprietary electronics.

Factors affecting cost can include:

Diagnostic complexity
PCB design
Component availability
Damage severity
Number of failed components
Previous repair attempts
Required testing
Programming requirements
Specialised components
Machine-level testing

For this reason, customers should avoid relying on a single generic price for all industrial PCB repairs.

The most accurate approach is to inspect the actual board.

Request a PCB Diagnosis in Industrial Area

If you have a 2-post car lift control board requiring testing, contact Pro-Logic Technologies.

When making your enquiry, provide:

PCB photographs

PCB part number

Lift manufacturer

Lift model

Fault description

Previous repair history

Any available wiring diagram

This allows us to understand the job before the board arrives.

Industrial Area Nairobi PCB Repair Service

Our location focus is Industrial Area, Nairobi.

This makes the service particularly relevant to:

Automotive garages
Engineering workshops
Industrial businesses
Machinery operators
Equipment dealers
Manufacturing businesses
Technical service companies
Electronics technicians
Workshop owners

If your business operates equipment with an electronic control board, you can contact us when the board develops a suspected fault.

Automotive Equipment Electronics Repair

Modern automotive workshops use a wide range of electronically controlled equipment.

When the electronics fail, mechanical equipment may remain perfectly usable but become impossible to operate.

PCB diagnosis can help determine whether the electronic control system is the source of the problem.

This applies particularly to equipment such as vehicle lifts and other workshop machinery.

Two-Post Vehicle Lift Control System

A two-post vehicle lift typically relies on coordinated operation between electrical controls and mechanical or hydraulic components.

The electronic controller may determine when particular functions are allowed to operate.

Safety inputs can also prevent movement when certain conditions are not satisfied.

Therefore, troubleshooting must consider the complete control sequence.

Vehicle Lift Safety

Vehicle lifts can raise heavy vehicles and should be treated as safety-critical equipment.

PCB repair is only one aspect of returning a vehicle lift to service.

After electronic repair, the complete lift should be properly inspected and tested according to the manufacturer's requirements and applicable safety procedures.

The electronic repair of a PCB should not be interpreted as certification of the complete lifting system.

Before returning the lift to normal operation, qualified personnel should verify the appropriate:

Safety locks
Structural components
Hydraulic system
Mechanical components
Electrical wiring
Emergency stop system
Limit switches
Control functions
Other safety features

Do not operate a vehicle lift if you suspect that its safety system is defective.

Industrial Electronics Troubleshooting

Industrial electronics troubleshooting requires patience and a logical process.

The goal is not simply to find something that looks damaged.

The goal is to determine:

What failed?

Why did it fail?

What other components may have been affected?

Can the failed section be repaired?

Is repair economically sensible?

This approach is particularly valuable when dealing with industrial control equipment.

Common Industrial PCB Faults

Some common faults encountered in electronic control systems include:

Power supply failure
Relay failure
Driver transistor failure
Shorted semiconductor
Failed regulator
Damaged protection circuit
Broken PCB track
Cracked solder joint
Corroded connector
Failed capacitor
Surge damage
Overheating
Moisture damage
Wiring-related damage

The actual fault varies from board to board.

Signs Your Control PCB May Need Diagnosis

Consider having the board assessed if:

Equipment suddenly stops responding.
A control output has disappeared.
Relays no longer activate.
A board repeatedly blows a fuse.
The machine operates intermittently.
A PCB overheats.
There is visible burning.
Equipment stopped after a power surge.
The machine works only sometimes.
A replacement PCB is difficult to source.
A technician has identified the PCB as a suspected fault.

Do Not Keep Resetting a Faulty Machine

Repeatedly switching a faulty machine on and off may not solve the underlying problem.

If the equipment repeatedly trips, blows fuses, overheats or behaves abnormally, it is better to investigate the fault.

This is particularly important with industrial equipment and vehicle lifts.

Industrial PCB Diagnosis for Technicians

If you are an electrical technician, automotive technician or machinery technician and have already isolated a suspected PCB fault, you can provide the board and available diagnostic information.

Useful information includes:

Expected input voltage
Expected output
Fault condition
Wiring diagram
Test results
Machine model
PCB number

This can make PCB-level troubleshooting more efficient.

PCB Repair for Equipment Dealers

Equipment dealers may occasionally receive machines with failed electronic control boards.

If the original manufacturer board is unavailable or expensive, diagnosis can determine whether the existing board is repairable.

The board should be assessed before promising a repair to the end customer.

Industrial PCB Repair for Manufacturing Equipment

Manufacturing systems can depend on electronic control boards for:

Motor control
Sensor processing
Safety functions
Relay control
Actuator operation
Operator interfaces
Automation

A PCB fault can therefore stop a production process.

Early diagnosis can help determine the most practical repair path.

Electronic Control Module Repair

Electronic control modules can vary significantly in complexity.

Some are simple relay-based systems.

Others use microprocessors and sophisticated digital circuitry.

The repair strategy therefore depends on the design.

We assess the individual board rather than applying the same repair procedure to every PCB.

Power Supply PCB Diagnosis

The power supply is one of the most important sections of many control boards.

A defective supply can cause:

No operation
Intermittent operation
Relay failure
Processor resets
Incorrect output
Overheating
Fuse failure

Testing the supply section is therefore often an important part of PCB diagnosis.

Control Board Relay Testing

Relays can be tested for:

Coil continuity
Coil voltage
Contact operation
Contact resistance
Driver operation

A relay that appears faulty may actually be receiving incorrect control voltage.

This is another reason why testing the surrounding circuit is important.

Industrial PCB Repair and Preventive Maintenance

Preventive maintenance can reduce the risk of unexpected failures.

Businesses should consider periodically checking:

Electrical connections
Control cabinets
Cooling
Ventilation
Moisture
Dust
Connectors
Power quality
Unusual heating
Repeated fuse failures

If equipment begins operating intermittently, investigate the problem early.

Local Industrial PCB Repair in Nairobi

Searching for a nearby repair service can be especially useful when dealing with industrial equipment because boards may be large, delicate or difficult to transport.

For customers in Nairobi, Industrial Area is a practical location for accessing technical and industrial services.

Pro-Logic Technologies focuses on providing electronic repair solutions from this area.

Search Terms Customers May Use

Customers looking for this service may search online using phrases such as:

Industrial PCB repair Nairobi
PCB repair Industrial Area Nairobi
Industrial PCB testing Nairobi
Industrial control board repair Nairobi
Control PCB diagnosis Nairobi
Machine PCB repair Nairobi
Industrial electronics repair Nairobi
Car lift PCB repair Nairobi
2 post lift PCB repair Nairobi
Two post car lift control board repair
Vehicle lift control board repair Nairobi
Car lift controller repair Nairobi
Garage equipment PCB repair Nairobi
Industrial control board testing Nairobi
Electronic control board repair Kenya
Industrial electronic repair Kenya
PCB troubleshooting Nairobi
Control board diagnostics Nairobi

This service page is designed to provide useful information for customers searching for these solutions.

Frequently Asked Questions

Do you repair industrial control PCBs in Industrial Area Nairobi?

Yes. Pro-Logic Technologies provides industrial control PCB diagnosis, testing and repair services in Industrial Area, Nairobi, depending on the specific board and fault.

Do you repair 2-post car lift control boards?

We can assess two-post car lift control boards for electronic faults and determine whether repair is practical.

Can you test my car lift PCB?

Yes. The board can be assessed for identifiable electrical and electronic faults, subject to its design and available testing information.

What is the charge for diagnosis?

The diagnostic charge depends on the PCB, its complexity and the amount of testing required. Contact us with photographs and board details for assessment.

Can I get the diagnosis before paying for repair?

Diagnosis and repair can be treated as separate stages. The board can first be assessed so you can make an informed decision about proceeding with repair.

Can you repair a burnt PCB?

A burnt PCB may be repairable depending on the extent and location of the damage. The underlying cause must also be investigated.

Can you repair boards damaged by power surges?

Surge-damaged boards can be assessed. The extent of damage determines whether repair is practical.

Can you repair old industrial PCBs?

Yes, older boards can be assessed. Repairability depends on component availability and the physical and electrical condition of the PCB.

Can you test the board without the complete vehicle lift?

Some testing can be performed separately, but complete functional testing may require machine-specific inputs, wiring or external components.

Do I need the wiring diagram?

It is not always mandatory, but a wiring diagram can be very helpful for understanding the board's intended function.

Can you diagnose the complete vehicle lift?

PCB diagnosis focuses on the electronic control board. Complete lift inspection may require additional mechanical, hydraulic and electrical expertise.

Can you guarantee that the PCB can be repaired?

No. Repairability can only be confirmed after inspection and diagnosis.

Can you replace the PCB if it cannot be repaired?

If a suitable replacement is available, replacement can be considered. Availability depends on the manufacturer, model and board number.

How to Contact Pro-Logic Technologies

If you have an industrial control board that needs diagnosis, send us the relevant information.

For a 2-post car lift control PCB, send:

1. A clear photograph of the PCB

2. A photograph of the PCB label or part number

3. The lift manufacturer

4. The lift model

5. A description of the fault

6. A photograph of the control panel

7. A photograph of the complete lift if available

8. Any wiring diagram or technical documentation

This information helps us understand the job before the board is submitted.

Why Professional Diagnosis Matters

Industrial machinery can be expensive and downtime can be disruptive.

Replacing parts without identifying the fault can increase costs.

A proper diagnosis can help establish:

Whether the PCB is faulty
Which circuit section may be affected
Whether repair is practical
Whether replacement should be considered
Whether the fault may actually be outside the PCB

This gives the customer better information before making a repair decision.

Your Industrial PCB May Be Repairable

If your industrial equipment has stopped working, do not automatically assume that the complete control board needs replacement.

The fault could involve a single component, power supply, relay, driver circuit, connector, solder joint or PCB track.

In other cases, the board may have severe damage and replacement may be the better option.

The first step is diagnosis.

Contact Pro-Logic Technologies in Industrial Area Nairobi

If you have a 2-post car lift control board that needs testing, contact Pro-Logic Technologies in Industrial Area, Nairobi.

We provide:

Industrial Control PCB Diagnosis

Industrial PCB Testing

Control Board Troubleshooting

Component-Level PCB Repair

Car Lift Control Board Diagnosis

2-Post Vehicle Lift PCB Testing

Industrial Electronics Repair

Machine Control Board Repair

Relay and Power Supply Board Diagnosis

Our approach is straightforward:

Test the board.

Identify the fault.

Determine whether repair is practical.

Recommend the appropriate solution.

If you are in Nairobi and have an industrial control PCB waiting for diagnosis, send us photographs of the board, the part number and a description of the problem.

Pro-Logic Technologies – Industrial Electronic Repair Solutions in Industrial Area, Nairobi, Kenya.